commit e692f66fab3019ca8f45463df165177505f38caa Author: Greg Kroah-Hartman Date: Tue Jul 3 11:23:18 2018 +0200 Linux 4.9.111 commit 35fd10aeb2248cc7f8d3d48ccc2eff1cf19918f4 Author: Bjørn Mork Date: Fri Jun 8 09:15:24 2018 +0200 cdc_ncm: avoid padding beyond end of skb commit 49c2c3f246e2fc3009039e31a826333dcd0283cd upstream. Commit 4a0e3e989d66 ("cdc_ncm: Add support for moving NDP to end of NCM frame") added logic to reserve space for the NDP at the end of the NTB/skb. This reservation did not take the final alignment of the NDP into account, causing us to reserve too little space. Additionally the padding prior to NDP addition did not ensure there was enough space for the NDP. The NTB/skb with the NDP appended would then exceed the configured max size. This caused the final padding of the NTB to use a negative count, padding to almost INT_MAX, and resulting in: [60103.825970] BUG: unable to handle kernel paging request at ffff9641f2004000 [60103.825998] IP: __memset+0x24/0x30 [60103.826001] PGD a6a06067 P4D a6a06067 PUD 4f65a063 PMD 72003063 PTE 0 [60103.826013] Oops: 0002 [#1] SMP NOPTI [60103.826018] Modules linked in: (removed( [60103.826158] CPU: 0 PID: 5990 Comm: Chrome_DevTools Tainted: G O 4.14.0-3-amd64 #1 Debian 4.14.17-1 [60103.826162] Hardware name: LENOVO 20081 BIOS 41CN28WW(V2.04) 05/03/2012 [60103.826166] task: ffff964193484fc0 task.stack: ffffb2890137c000 [60103.826171] RIP: 0010:__memset+0x24/0x30 [60103.826174] RSP: 0000:ffff964316c03b68 EFLAGS: 00010216 [60103.826178] RAX: 0000000000000000 RBX: 00000000fffffffd RCX: 000000001ffa5000 [60103.826181] RDX: 0000000000000005 RSI: 0000000000000000 RDI: ffff9641f2003ffc [60103.826184] RBP: ffff964192f6c800 R08: 00000000304d434e R09: ffff9641f1d2c004 [60103.826187] R10: 0000000000000002 R11: 00000000000005ae R12: ffff9642e6957a80 [60103.826190] R13: ffff964282ff2ee8 R14: 000000000000000d R15: ffff9642e4843900 [60103.826194] FS: 00007f395aaf6700(0000) GS:ffff964316c00000(0000) knlGS:0000000000000000 [60103.826197] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [60103.826200] CR2: ffff9641f2004000 CR3: 0000000013b0c000 CR4: 00000000000006f0 [60103.826204] Call Trace: [60103.826212] [60103.826225] cdc_ncm_fill_tx_frame+0x5e3/0x740 [cdc_ncm] [60103.826236] cdc_ncm_tx_fixup+0x57/0x70 [cdc_ncm] [60103.826246] usbnet_start_xmit+0x5d/0x710 [usbnet] [60103.826254] ? netif_skb_features+0x119/0x250 [60103.826259] dev_hard_start_xmit+0xa1/0x200 [60103.826267] sch_direct_xmit+0xf2/0x1b0 [60103.826273] __dev_queue_xmit+0x5e3/0x7c0 [60103.826280] ? ip_finish_output2+0x263/0x3c0 [60103.826284] ip_finish_output2+0x263/0x3c0 [60103.826289] ? ip_output+0x6c/0xe0 [60103.826293] ip_output+0x6c/0xe0 [60103.826298] ? ip_forward_options+0x1a0/0x1a0 [60103.826303] tcp_transmit_skb+0x516/0x9b0 [60103.826309] tcp_write_xmit+0x1aa/0xee0 [60103.826313] ? sch_direct_xmit+0x71/0x1b0 [60103.826318] tcp_tasklet_func+0x177/0x180 [60103.826325] tasklet_action+0x5f/0x110 [60103.826332] __do_softirq+0xde/0x2b3 [60103.826337] irq_exit+0xae/0xb0 [60103.826342] do_IRQ+0x81/0xd0 [60103.826347] common_interrupt+0x98/0x98 [60103.826351] [60103.826355] RIP: 0033:0x7f397bdf2282 [60103.826358] RSP: 002b:00007f395aaf57d8 EFLAGS: 00000206 ORIG_RAX: ffffffffffffff6e [60103.826362] RAX: 0000000000000000 RBX: 00002f07bc6d0900 RCX: 00007f39752d7fe7 [60103.826365] RDX: 0000000000000022 RSI: 0000000000000147 RDI: 00002f07baea02c0 [60103.826368] RBP: 0000000000000001 R08: 0000000000000000 R09: 0000000000000000 [60103.826371] R10: 00000000ffffffff R11: 0000000000000000 R12: 00002f07baea02c0 [60103.826373] R13: 00002f07bba227a0 R14: 00002f07bc6d090c R15: 0000000000000000 [60103.826377] Code: 90 90 90 90 90 90 90 0f 1f 44 00 00 49 89 f9 48 89 d1 83 e2 07 48 c1 e9 03 40 0f b6 f6 48 b8 01 01 01 01 01 01 01 01 48 0f af c6 48 ab 89 d1 f3 aa 4c 89 c8 c3 90 49 89 f9 40 88 f0 48 89 d1 [60103.826442] RIP: __memset+0x24/0x30 RSP: ffff964316c03b68 [60103.826444] CR2: ffff9641f2004000 Commit e1069bbfcf3b ("net: cdc_ncm: Reduce memory use when kernel memory low") made this bug much more likely to trigger by reducing the NTB size under memory pressure. Link: https://bugs.debian.org/893393 Reported-by: Горбешко Богдан Reported-and-tested-by: Dennis Wassenberg Cc: Enrico Mioso Fixes: 4a0e3e989d66 ("cdc_ncm: Add support for moving NDP to end of NCM frame") [ bmork: tx_curr_size => tx_max and context fixup for v4.12 and older ] Signed-off-by: Bjørn Mork Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman commit f2bc5d18d26350423446fcc073ad8750c20ec498 Author: Mike Snitzer Date: Tue Jun 26 12:04:23 2018 -0400 dm thin: handle running out of data space vs concurrent discard commit a685557fbbc3122ed11e8ad3fa63a11ebc5de8c3 upstream. Discards issued to a DM thin device can complete to userspace (via fstrim) _before_ the metadata changes associated with the discards is reflected in the thinp superblock (e.g. free blocks). As such, if a user constructs a test that loops repeatedly over these steps, block allocation can fail due to discards not having completed yet: 1) fill thin device via filesystem file 2) remove file 3) fstrim From initial report, here: https://www.redhat.com/archives/dm-devel/2018-April/msg00022.html "The root cause of this issue is that dm-thin will first remove mapping and increase corresponding blocks' reference count to prevent them from being reused before DISCARD bios get processed by the underlying layers. However. increasing blocks' reference count could also increase the nr_allocated_this_transaction in struct sm_disk which makes smd->old_ll.nr_allocated + smd->nr_allocated_this_transaction bigger than smd->old_ll.nr_blocks. In this case, alloc_data_block() will never commit metadata to reset the begin pointer of struct sm_disk, because sm_disk_get_nr_free() always return an underflow value." While there is room for improvement to the space-map accounting that thinp is making use of: the reality is this test is inherently racey and will result in the previous iteration's fstrim's discard(s) completing vs concurrent block allocation, via dd, in the next iteration of the loop. No amount of space map accounting improvements will be able to allow user's to use a block before a discard of that block has completed. So the best we can really do is allow DM thinp to gracefully handle such aggressive use of all the pool's data by degrading the pool into out-of-data-space (OODS) mode. We _should_ get that behaviour already (if space map accounting didn't falsely cause alloc_data_block() to believe free space was available).. but short of that we handle the current reality that dm_pool_alloc_data_block() can return -ENOSPC. Reported-by: Dennis Yang Cc: stable@vger.kernel.org Signed-off-by: Mike Snitzer Signed-off-by: Greg Kroah-Hartman commit 17057c59bd11911cff0f62715efcb556bab05ade Author: Keith Busch Date: Tue Jun 26 09:14:58 2018 -0600 block: Fix transfer when chunk sectors exceeds max commit 15bfd21fbc5d35834b9ea383dc458a1f0c9e3434 upstream. A device may have boundary restrictions where the number of sectors between boundaries exceeds its max transfer size. In this case, we need to cap the max size to the smaller of the two limits. Reported-by: Jitendra Bhivare Tested-by: Jitendra Bhivare Cc: Reviewed-by: Martin K. Petersen Signed-off-by: Keith Busch Signed-off-by: Jens Axboe Signed-off-by: Greg Kroah-Hartman commit afd82d0757b37a346fbc557c5974c0f0de1bb0d2 Author: Takashi Iwai Date: Fri Jun 22 12:17:45 2018 +0200 ALSA: hda/realtek - Add a quirk for FSC ESPRIMO U9210 commit 275ec0cb946cb75ac8977f662e608fce92f8b8a8 upstream. Fujitsu Seimens ESPRIMO Mobile U9210 requires the same fixup as H270 for the correct pin configs. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200107 Cc: Signed-off-by: Takashi Iwai Signed-off-by: Greg Kroah-Hartman commit 6008de291a2beab8028d04df9b0ea930e4fe4ce0 Author: Takashi Iwai Date: Wed Jun 13 12:43:10 2018 +0200 ALSA: hda/realtek - Fix pop noise on Lenovo P50 & co commit d5a6cabf02210b896a60eee7c04c670ee9ba6dca upstream. Some Lenovo laptops, e.g. Lenovo P50, showed the pop noise at resume or runtime resume. It turned out to be reduced by applying alc_no_shutup() just like TPT440 quirk does. Since there are many Lenovo models showing the same behavior, put this workaround in ALC269_FIXUP_THINKPAD_ACPI entry so that it's applied commonly to all such Lenovo machines. Reported-by: Hans de Goede Tested-by: Benjamin Berg Cc: Signed-off-by: Takashi Iwai Signed-off-by: Greg Kroah-Hartman commit 58d8103113ea911ed23cfd31c866f14c43773fb7 Author: ??? Date: Thu Jun 21 17:15:32 2018 -0700 Input: elantech - fix V4 report decoding for module with middle key commit e0ae2519ca004a628fa55aeef969c37edce522d3 upstream. Some touchpad has middle key and it will be indicated in bit 2 of packet[0]. We need to fix V4 formation's byte mask to prevent error decoding. Signed-off-by: KT Liao Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov Signed-off-by: Greg Kroah-Hartman commit 465e965f64358fdeeb35287bd7a6dc06b261fb7b Author: Aaron Ma Date: Thu Jun 21 17:14:01 2018 -0700 Input: elantech - enable middle button of touchpads on ThinkPad P52 commit 24bb555e6e46d96e2a954aa0295029a81cc9bbaa upstream. PNPID is better way to identify the type of touchpads. Enable middle button support on 2 types of touchpads on Lenovo P52. Cc: stable@vger.kernel.org Signed-off-by: Aaron Ma Reviewed-by: Benjamin Tissoires Signed-off-by: Dmitry Torokhov Signed-off-by: Greg Kroah-Hartman commit 54ae564b35423f25b763bc9e01b489d9f11c034e Author: Ben Hutchings Date: Tue Jun 19 11:17:32 2018 -0700 Input: elan_i2c_smbus - fix more potential stack buffer overflows commit 50fc7b61959af4b95fafce7fe5dd565199e0b61a upstream. Commit 40f7090bb1b4 ("Input: elan_i2c_smbus - fix corrupted stack") fixed most of the functions using i2c_smbus_read_block_data() to allocate a buffer with the maximum block size. However three functions were left unchanged: * In elan_smbus_initialize(), increase the buffer size in the same way. * In elan_smbus_calibrate_result(), the buffer is provided by the caller (calibrate_store()), so introduce a bounce buffer. Also name the result buffer size. * In elan_smbus_get_report(), the buffer is provided by the caller but happens to be the right length. Add a compile-time assertion to ensure this remains the case. Cc: # 3.19+ Signed-off-by: Ben Hutchings Reviewed-by: Benjamin Tissoires Signed-off-by: Dmitry Torokhov Signed-off-by: Greg Kroah-Hartman commit 2a1b1234d0502237872f6a11016061328528b86d Author: Jan Kara Date: Wed Jun 13 12:09:22 2018 +0200 udf: Detect incorrect directory size commit fa65653e575fbd958bdf5fb9c4a71a324e39510d upstream. Detect when a directory entry is (possibly partially) beyond directory size and return EIO in that case since it means the filesystem is corrupted. Otherwise directory operations can further corrupt the directory and possibly also oops the kernel. CC: Anatoly Trosinenko CC: stable@vger.kernel.org Reported-and-tested-by: Anatoly Trosinenko Signed-off-by: Jan Kara Signed-off-by: Greg Kroah-Hartman commit 3cac26f2a2c66f755e033ca944d02433be684556 Author: Boris Ostrovsky Date: Thu Jun 21 13:29:44 2018 -0400 xen: Remove unnecessary BUG_ON from __unbind_from_irq() commit eef04c7b3786ff0c9cb1019278b6c6c2ea0ad4ff upstream. Commit 910f8befdf5b ("xen/pirq: fix error path cleanup when binding MSIs") fixed a couple of errors in error cleanup path of xen_bind_pirq_msi_to_irq(). This cleanup allowed a call to __unbind_from_irq() with an unbound irq, which would result in triggering the BUG_ON there. Since there is really no reason for the BUG_ON (xen_free_irq() can operate on unbound irqs) we can remove it. Reported-by: Ben Hutchings Signed-off-by: Boris Ostrovsky Cc: stable@vger.kernel.org Reviewed-by: Juergen Gross Signed-off-by: Juergen Gross Signed-off-by: Greg Kroah-Hartman commit 6d28f2d64cf5ddf6c55f7a3a954dd9a34b72862b Author: Dan Williams Date: Thu Jun 14 15:26:24 2018 -0700 mm: fix devmem_is_allowed() for sub-page System RAM intersections commit 2bdce74412c249ac01dfe36b6b0043ffd7a5361e upstream. Hussam reports: I was poking around and for no real reason, I did cat /dev/mem and strings /dev/mem. Then I saw the following warning in dmesg. I saved it and rebooted immediately. memremap attempted on mixed range 0x000000000009c000 size: 0x1000 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 11810 at kernel/memremap.c:98 memremap+0x104/0x170 [..] Call Trace: xlate_dev_mem_ptr+0x25/0x40 read_mem+0x89/0x1a0 __vfs_read+0x36/0x170 The memremap() implementation checks for attempts to remap System RAM with MEMREMAP_WB and instead redirects those mapping attempts to the linear map. However, that only works if the physical address range being remapped is page aligned. In low memory we have situations like the following: 00000000-00000fff : Reserved 00001000-0009fbff : System RAM 0009fc00-0009ffff : Reserved ...where System RAM intersects Reserved ranges on a sub-page page granularity. Given that devmem_is_allowed() special cases any attempt to map System RAM in the first 1MB of memory, replace page_is_ram() with the more precise region_intersects() to trap attempts to map disallowed ranges. Link: https://bugzilla.kernel.org/show_bug.cgi?id=199999 Link: http://lkml.kernel.org/r/152856436164.18127.2847888121707136898.stgit@dwillia2-desk3.amr.corp.intel.com Fixes: 92281dee825f ("arch: introduce memremap()") Signed-off-by: Dan Williams Reported-by: Hussam Al-Tayeb Tested-by: Hussam Al-Tayeb Cc: Christoph Hellwig Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds Signed-off-by: Greg Kroah-Hartman commit 1f00b1fc77752bb27b6b696fd7fceeda921ac0fa Author: Dongsheng Yang Date: Mon Jun 4 06:24:37 2018 -0400 rbd: flush rbd_dev->watch_dwork after watch is unregistered commit 23edca864951250af845a11da86bb3ea63522ed2 upstream. There is a problem if we are going to unmap a rbd device and the watch_dwork is going to queue delayed work for watch: unmap Thread watch Thread timer do_rbd_remove cancel_tasks_sync(rbd_dev) queue_delayed_work for watch destroy_workqueue(rbd_dev->task_wq) drain_workqueue(wq) destroy other resources in wq call_timer_fn __queue_work() Then the delayed work escape the cancel_tasks_sync() and destroy_workqueue() and we will get an user-after-free call trace: BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 PGD 0 P4D 0 Oops: 0000 [#1] SMP PTI Modules linked in: CPU: 7 PID: 0 Comm: swapper/7 Tainted: G OE 4.17.0-rc6+ #13 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 RIP: 0010:__queue_work+0x6a/0x3b0 RSP: 0018:ffff9427df1c3e90 EFLAGS: 00010086 RAX: ffff9427deca8400 RBX: 0000000000000000 RCX: 0000000000000000 RDX: ffff9427deca8400 RSI: ffff9427df1c3e50 RDI: 0000000000000000 RBP: ffff942783e39e00 R08: ffff9427deca8400 R09: ffff9427df1c3f00 R10: 0000000000000004 R11: 0000000000000005 R12: ffff9427cfb85970 R13: 0000000000002000 R14: 000000000001eca0 R15: 0000000000000007 FS: 0000000000000000(0000) GS:ffff9427df1c0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 00000004c900a005 CR4: 00000000000206e0 Call Trace: ? __queue_work+0x3b0/0x3b0 call_timer_fn+0x2d/0x130 run_timer_softirq+0x16e/0x430 ? tick_sched_timer+0x37/0x70 __do_softirq+0xd2/0x280 irq_exit+0xd5/0xe0 smp_apic_timer_interrupt+0x6c/0x130 apic_timer_interrupt+0xf/0x20 [ Move rbd_dev->watch_dwork cancellation so that rbd_reregister_watch() either bails out early because the watch is UNREGISTERED at that point or just gets cancelled. ] Cc: stable@vger.kernel.org Fixes: 99d1694310df ("rbd: retry watch re-registration periodically") Signed-off-by: Dongsheng Yang Reviewed-by: Ilya Dryomov Signed-off-by: Ilya Dryomov Signed-off-by: Greg Kroah-Hartman commit 037aca0e2fc22dcff17c38b38d9efab5e0d4b96e Author: Hans de Goede Date: Thu Apr 26 14:10:23 2018 +0200 pwm: lpss: platform: Save/restore the ctrl register over a suspend/resume commit 1d375b58c12f08d8570b30b865def4734517f04f upstream. On some devices the contents of the ctrl register get lost over a suspend/resume and the PWM comes back up disabled after the resume. This is seen on some Bay Trail devices with the PWM in ACPI enumerated mode, so it shows up as a platform device instead of a PCI device. If we still think it is enabled and then try to change the duty-cycle after this, we end up with a "PWM_SW_UPDATE was not cleared" error and the PWM is stuck in that state from then on. This commit adds suspend and resume pm callbacks to the pwm-lpss-platform code, which save/restore the ctrl register over a suspend/resume, fixing this. Note that: 1) There is no need to do this over a runtime suspend, since we only runtime suspend when disabled and then we properly set the enable bit and reprogram the timings when we re-enable the PWM. 2) This may be happening on more systems then we realize, but has been covered up sofar by a bug in the acpi-lpss.c code which was save/restoring the regular device registers instead of the lpss private registers due to lpss_device_desc.prv_offset not being set. This is fixed by a later patch in this series. Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede Reviewed-by: Andy Shevchenko Signed-off-by: Thierry Reding Signed-off-by: Greg Kroah-Hartman commit c38bac75d1c21b09764a882b520b0ad33749ac10 Author: Alexandr Savca Date: Thu Jun 21 17:12:54 2018 -0700 Input: elan_i2c - add ELAN0618 (Lenovo v330 15IKB) ACPI ID commit 8938fc7b8fe9ccfa11751ead502a8d385b607967 upstream. Add ELAN0618 to the list of supported touchpads; this ID is used in Lenovo v330 15IKB devices. Signed-off-by: Alexandr Savca Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov Signed-off-by: Greg Kroah-Hartman commit 7673ca3c93414faf90fa2a3c339f1f625415fecb Author: Kees Cook Date: Fri May 11 18:24:12 2018 +1000 video: uvesafb: Fix integer overflow in allocation commit 9f645bcc566a1e9f921bdae7528a01ced5bc3713 upstream. cmap->len can get close to INT_MAX/2, allowing for an integer overflow in allocation. This uses kmalloc_array() instead to catch the condition. Reported-by: Dr Silvio Cesare of InfoSect Fixes: 8bdb3a2d7df48 ("uvesafb: the driver core") Cc: stable@vger.kernel.org Signed-off-by: Kees Cook Signed-off-by: Greg Kroah-Hartman commit cdc83c366977044d7717d56f6bb1aa247e1dc582 Author: Trond Myklebust Date: Sat Jun 9 12:43:06 2018 -0400 NFSv4: Revert commit 5f83d86cf531d ("NFSv4.x: Fix wraparound issues..") commit fc40724fc6731d90cc7fb6d62d66135f85a33dd2 upstream. The correct behaviour for NFSv4 sequence IDs is to wrap around to the value 0 after 0xffffffff. See https://tools.ietf.org/html/rfc5661#section-2.10.6.1 Fixes: 5f83d86cf531d ("NFSv4.x: Fix wraparound issues when validing...") Cc: stable@vger.kernel.org # 4.6+ Signed-off-by: Trond Myklebust Signed-off-by: Greg Kroah-Hartman commit 5b7f582e808d6b39eb0751deb1b6685813b05847 Author: Dave Wysochanski Date: Tue May 29 17:47:30 2018 -0400 NFSv4: Fix possible 1-byte stack overflow in nfs_idmap_read_and_verify_message commit d68894800ec5712d7ddf042356f11e36f87d7f78 upstream. In nfs_idmap_read_and_verify_message there is an incorrect sprintf '%d' that converts the __u32 'im_id' from struct idmap_msg to 'id_str', which is a stack char array variable of length NFS_UINT_MAXLEN == 11. If a uid or gid value is > 2147483647 = 0x7fffffff, the conversion overflows into a negative value, for example: crash> p (unsigned) (0x80000000) $1 = 2147483648 crash> p (signed) (0x80000000) $2 = -2147483648 The '-' sign is written to the buffer and this causes a 1 byte overflow when the NULL byte is written, which corrupts kernel stack memory. If CONFIG_CC_STACKPROTECTOR_STRONG is set we see a stack-protector panic: [11558053.616565] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: ffffffffa05b8a8c [11558053.639063] CPU: 6 PID: 9423 Comm: rpc.idmapd Tainted: G W ------------ T 3.10.0-514.el7.x86_64 #1 [11558053.641990] Hardware name: Red Hat OpenStack Compute, BIOS 1.10.2-3.el7_4.1 04/01/2014 [11558053.644462] ffffffff818c7bc0 00000000b1f3aec1 ffff880de0f9bd48 ffffffff81685eac [11558053.646430] ffff880de0f9bdc8 ffffffff8167f2b3 ffffffff00000010 ffff880de0f9bdd8 [11558053.648313] ffff880de0f9bd78 00000000b1f3aec1 ffffffff811dcb03 ffffffffa05b8a8c [11558053.650107] Call Trace: [11558053.651347] [] dump_stack+0x19/0x1b [11558053.653013] [] panic+0xe3/0x1f2 [11558053.666240] [] ? kfree+0x103/0x140 [11558053.682589] [] ? idmap_pipe_downcall+0x1cc/0x1e0 [nfsv4] [11558053.689710] [] __stack_chk_fail+0x1b/0x30 [11558053.691619] [] idmap_pipe_downcall+0x1cc/0x1e0 [nfsv4] [11558053.693867] [] rpc_pipe_write+0x56/0x70 [sunrpc] [11558053.695763] [] vfs_write+0xbd/0x1e0 [11558053.702236] [] ? task_work_run+0xac/0xe0 [11558053.704215] [] SyS_write+0x7f/0xe0 [11558053.709674] [] system_call_fastpath+0x16/0x1b Fix this by calling the internally defined nfs_map_numeric_to_string() function which properly uses '%u' to convert this __u32. For consistency, also replace the one other place where snprintf is called. Signed-off-by: Dave Wysochanski Reported-by: Stephen Johnston Fixes: cf4ab538f1516 ("NFSv4: Fix the string length returned by the idmapper") Cc: stable@vger.kernel.org # v3.4+ Signed-off-by: Trond Myklebust Signed-off-by: Greg Kroah-Hartman commit 40d79a61957a7d59b079d30fbbc5e51c3b9b239a Author: Scott Mayhew Date: Mon May 7 09:01:08 2018 -0400 nfsd: restrict rd_maxcount to svc_max_payload in nfsd_encode_readdir commit 9c2ece6ef67e9d376f32823086169b489c422ed0 upstream. nfsd4_readdir_rsize restricts rd_maxcount to svc_max_payload when estimating the size of the readdir reply, but nfsd_encode_readdir restricts it to INT_MAX when encoding the reply. This can result in log messages like "kernel: RPC request reserved 32896 but used 1049444". Restrict rd_dircount similarly (no reason it should be larger than svc_max_payload). Signed-off-by: Scott Mayhew Cc: stable@vger.kernel.org Signed-off-by: J. Bruce Fields Signed-off-by: Greg Kroah-Hartman commit dc00f08645be1f6a1319af6c6c1117137f787efc Author: Mauro Carvalho Chehab Date: Thu Apr 5 05:30:52 2018 -0400 media: dvb_frontend: fix locking issues at dvb_frontend_get_event() commit 76d81243a487c09619822ef8e7201a756e58a87d upstream. As warned by smatch: drivers/media/dvb-core/dvb_frontend.c:314 dvb_frontend_get_event() warn: inconsistent returns 'sem:&fepriv->sem'. Locked on: line 288 line 295 line 306 line 314 Unlocked on: line 303 The lock implementation for get event is wrong, as, if an interrupt occurs, down_interruptible() will fail, and the routine will call up() twice when userspace calls the ioctl again. The bad code is there since when Linux migrated to git, in 2005. Cc: stable@vger.kernel.org Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Greg Kroah-Hartman commit 1a4726ba1dedcdb92bc15a70e65150e9222ceed1 Author: Kai-Heng Feng Date: Mon Mar 26 02:06:16 2018 -0400 media: cx231xx: Add support for AverMedia DVD EZMaker 7 commit 29e61d6ef061b012d320327af7dbb3990e75be45 upstream. User reports AverMedia DVD EZMaker 7 can be driven by VIDEO_GRABBER. Add the device to the id_table to make it work. BugLink: https://bugs.launchpad.net/bugs/1620762 Cc: stable@vger.kernel.org Signed-off-by: Kai-Heng Feng Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Greg Kroah-Hartman commit 1e6b50b6b68e25a8ff972a1e1279a40cd7adc4fd Author: Mauro Carvalho Chehab Date: Wed Apr 11 11:47:32 2018 -0400 media: v4l2-compat-ioctl32: prevent go past max size commit ea72fbf588ac9c017224dcdaa2019ff52ca56fee upstream. As warned by smatch: drivers/media/v4l2-core/v4l2-compat-ioctl32.c:879 put_v4l2_ext_controls32() warn: check for integer overflow 'count' The access_ok() logic should check for too big arrays too. Cc: stable@vger.kernel.org Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Greg Kroah-Hartman commit d6a267b4c5f9bb3db42e3fe6092d1059f08d03bf Author: Adrian Hunter Date: Thu Jun 7 14:30:02 2018 +0300 perf intel-pt: Fix packet decoding of CYC packets commit 621a5a327c1e36ffd7bb567f44a559f64f76358f upstream. Use a 64-bit type so that the cycle count is not limited to 32-bits. Signed-off-by: Adrian Hunter Cc: Jiri Olsa Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1528371002-8862-1-git-send-email-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo Signed-off-by: Greg Kroah-Hartman commit d129ab791de910a81bb53f0053d3476c26982aea Author: Adrian Hunter Date: Thu May 31 13:23:45 2018 +0300 perf intel-pt: Fix "Unexpected indirect branch" error commit 9fb523363f6e3984457fee95bb7019395384ffa7 upstream. Some Atom CPUs can produce FUP packets that contain NLIP (next linear instruction pointer) instead of CLIP (current linear instruction pointer). That will result in "Unexpected indirect branch" errors. Fix by comparing IP to NLIP in that case. Signed-off-by: Adrian Hunter Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1527762225-26024-5-git-send-email-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo Signed-off-by: Greg Kroah-Hartman commit 4213d9b8cdb10d4d29fd232898692a1a56c1fd58 Author: Adrian Hunter Date: Thu May 31 13:23:44 2018 +0300 perf intel-pt: Fix MTC timing after overflow commit dd27b87ab5fcf3ea1c060b5e3ab5d31cc78e9f4c upstream. On some platforms, overflows will clear before MTC wraparound, and there is no following TSC/TMA packet. In that case the previous TMA is valid. Since there will be a valid TMA either way, stop setting 'have_tma' to false upon overflow. Signed-off-by: Adrian Hunter Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1527762225-26024-4-git-send-email-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo Signed-off-by: Greg Kroah-Hartman commit 282f1f66b5a0f4875f2562144f5e5c80bc86dfc1 Author: Adrian Hunter Date: Thu May 31 13:23:43 2018 +0300 perf intel-pt: Fix decoding to accept CBR between FUP and corresponding TIP commit bd2e49ec48feb1855f7624198849eea4610e2286 upstream. It is possible to have a CBR packet between a FUP packet and corresponding TIP packet. Stop treating it as an error. Signed-off-by: Adrian Hunter Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1527762225-26024-3-git-send-email-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo Signed-off-by: Greg Kroah-Hartman commit 31606f7f56de573470f0b7037b764df381a87fa6 Author: Adrian Hunter Date: Thu May 31 13:23:42 2018 +0300 perf intel-pt: Fix sync_switch INTEL_PT_SS_NOT_TRACING commit dbcb82b93f3e8322891e47472c89e63058b81e99 upstream. sync_switch is a facility to synchronize decoding more closely with the point in the kernel when the context actually switched. In one case, INTEL_PT_SS_NOT_TRACING state was not correctly transitioning to INTEL_PT_SS_TRACING state due to a missing case clause. Add it. Signed-off-by: Adrian Hunter Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1527762225-26024-2-git-send-email-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo Signed-off-by: Greg Kroah-Hartman commit dfd2eff6f457f2193f0dfd0de5cb3aa49df3d3e9 Author: Adrian Hunter Date: Mon Jun 4 15:56:54 2018 +0300 perf tools: Fix symbol and object code resolution for vdso32 and vdsox32 commit aef4feace285f27c8ed35830a5d575bec7f3e90a upstream. Fix __kmod_path__parse() so that perf tools does not treat vdso32 and vdsox32 as kernel modules and fail to find the object. Signed-off-by: Adrian Hunter Cc: Jiri Olsa Cc: Wang Nan Cc: stable@vger.kernel.org Fixes: 1f121b03d058 ("perf tools: Deal with kernel module names in '[]' correctly") Link: http://lkml.kernel.org/r/1528117014-30032-3-git-send-email-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo Signed-off-by: Greg Kroah-Hartman commit 49d98a8e1f55f8406c45ce2b88eb4912d9877f67 Author: Andy Shevchenko Date: Tue Apr 24 18:00:10 2018 +0300 mfd: intel-lpss: Program REMAP register in PIO mode commit d28b62520830b2d0bffa2d98e81afc9f5e537e8b upstream. According to documentation REMAP register has to be programmed in either DMA or PIO mode of the slice. Move the DMA capability check below to let REMAP register be programmed in PIO mode. Cc: stable@vger.kernel.org # 4.3+ Fixes: 4b45efe85263 ("mfd: Add support for Intel Sunrisepoint LPSS devices") Signed-off-by: Andy Shevchenko Signed-off-by: Lee Jones Signed-off-by: Greg Kroah-Hartman commit 099fae46d8dfed70744321bbbd265cc7af2982f3 Author: Johan Hovold Date: Mon Nov 20 11:45:46 2017 +0100 backlight: tps65217_bl: Fix Device Tree node lookup commit 2b12dfa124dbadf391cb9a616aaa6b056823bf75 upstream. Fix child-node lookup during probe, which ended up searching the whole device tree depth-first starting at the parent rather than just matching on its children. This would only cause trouble if the child node is missing while there is an unrelated node named "backlight" elsewhere in the tree. Cc: stable # 3.7 Fixes: eebfdc17cc6c ("backlight: Add TPS65217 WLED driver") Signed-off-by: Johan Hovold Acked-by: Daniel Thompson Signed-off-by: Lee Jones Signed-off-by: Greg Kroah-Hartman commit a89e596f129117b902210c57599e198d1441ee93 Author: Johan Hovold Date: Mon Nov 20 11:45:45 2017 +0100 backlight: max8925_bl: Fix Device Tree node lookup commit d1cc0ec3da23e44c23712579515494b374f111c9 upstream. Fix child-node lookup during probe, which ended up searching the whole device tree depth-first starting at the parent rather than just matching on its children. To make things worse, the parent mfd node was also prematurely freed, while the child backlight node was leaked. Cc: stable # 3.9 Fixes: 47ec340cb8e2 ("mfd: max8925: Support dt for backlight") Signed-off-by: Johan Hovold Acked-by: Daniel Thompson Signed-off-by: Lee Jones Signed-off-by: Greg Kroah-Hartman commit 47f764c65c561ba1dcf7c6a9688c82202ede58ca Author: Johan Hovold Date: Mon Nov 20 11:45:44 2017 +0100 backlight: as3711_bl: Fix Device Tree node lookup commit 4a9c8bb2aca5b5a2a15744333729745dd9903562 upstream. Fix child-node lookup during probe, which ended up searching the whole device tree depth-first starting at the parent rather than just matching on its children. To make things worse, the parent mfd node was also prematurely freed. Cc: stable # 3.10 Fixes: 59eb2b5e57ea ("drivers/video/backlight/as3711_bl.c: add OF support") Signed-off-by: Johan Hovold Acked-by: Daniel Thompson Signed-off-by: Lee Jones Signed-off-by: Greg Kroah-Hartman commit da05be555697c3fdd3f1507b59917c1cc3b03566 Author: Silvio Cesare Date: Fri May 4 13:44:02 2018 +1000 UBIFS: Fix potential integer overflow in allocation commit 353748a359f1821ee934afc579cf04572406b420 upstream. There is potential for the size and len fields in ubifs_data_node to be too large causing either a negative value for the length fields or an integer overflow leading to an incorrect memory allocation. Likewise, when the len field is small, an integer underflow may occur. Signed-off-by: Silvio Cesare Fixes: 1e51764a3c2ac ("UBIFS: add new flash file system") Cc: stable@vger.kernel.org Signed-off-by: Kees Cook Signed-off-by: Greg Kroah-Hartman commit df15c6eeab46aac3622821e2659677c3eb4abf9d Author: Richard Weinberger Date: Mon May 28 22:04:32 2018 +0200 ubi: fastmap: Correctly handle interrupted erasures in EBA commit 781932375ffc6411713ee0926ccae8596ed0261c upstream. Fastmap cannot track the LEB unmap operation, therefore it can happen that after an interrupted erasure the mapping still looks good from Fastmap's point of view, while reading from the PEB will cause an ECC error and confuses the upper layer. Instead of teaching users of UBI how to deal with that, we read back the VID header and check for errors. If the PEB is empty or shows ECC errors we fixup the mapping and schedule the PEB for erasure. Fixes: dbb7d2a88d2a ("UBI: Add fastmap core") Cc: Reported-by: martin bayern Signed-off-by: Richard Weinberger Signed-off-by: Greg Kroah-Hartman commit 9eb99e738beb405cb69ce0c244e6bb0ee9666588 Author: Richard Weinberger Date: Wed May 16 22:17:03 2018 +0200 ubi: fastmap: Cancel work upon detach commit 6e7d80161066c99d12580d1b985cb1408bb58cf1 upstream. Ben Hutchings pointed out that 29b7a6fa1ec0 ("ubi: fastmap: Don't flush fastmap work on detach") does not really fix the problem, it just reduces the risk to hit the race window where fastmap work races against free()'ing ubi->volumes[]. The correct approach is making sure that no more fastmap work is in progress before we free ubi data structures. So we cancel fastmap work right after the ubi background thread is stopped. By setting ubi->thread_enabled to zero we make sure that no further work tries to wake the thread. Fixes: 29b7a6fa1ec0 ("ubi: fastmap: Don't flush fastmap work on detach") Fixes: 74cdaf24004a ("UBI: Fastmap: Fix memory leaks while closing the WL sub-system") Cc: stable@vger.kernel.org Cc: Ben Hutchings Cc: Martin Townsend Signed-off-by: Richard Weinberger Signed-off-by: Greg Kroah-Hartman commit ec7ee4d60f25f9a4ba264090b2671346d078ed2a Author: Srinivas Kandagatla Date: Mon Jun 4 10:39:01 2018 +0100 rpmsg: smd: do not use mananged resources for endpoints and channels commit 4a2e84c6ed85434ce7843e4844b4d3263f7e233b upstream. All the managed resources would be freed by the time release function is invoked. Handling such memory in qcom_smd_edge_release() would do bad things. Found this issue while testing Audio usecase where the dsp is started up and shutdown in a loop. This patch fixes this issue by using simple kzalloc for allocating channel->name and channel which is then freed in qcom_smd_edge_release(). Without this patch restarting a remoteproc would crash the system. Fixes: 53e2822e56c7 ("rpmsg: Introduce Qualcomm SMD backend") Cc: Signed-off-by: Srinivas Kandagatla Signed-off-by: Bjorn Andersson Signed-off-by: Greg Kroah-Hartman commit 486684887ab588309c3497785412bb67e162b7a6 Author: NeilBrown Date: Thu Apr 26 14:46:29 2018 +1000 md: fix two problems with setting the "re-add" device state. commit 011abdc9df559ec75779bb7c53a744c69b2a94c6 upstream. If "re-add" is written to the "state" file for a device which is faulty, this has an effect similar to removing and re-adding the device. It should take up the same slot in the array that it previously had, and an accelerated (e.g. bitmap-based) rebuild should happen. The slot that "it previously had" is determined by rdev->saved_raid_disk. However this is not set when a device fails (only when a device is added), and it is cleared when resync completes. This means that "re-add" will normally work once, but may not work a second time. This patch includes two fixes. 1/ when a device fails, record the ->raid_disk value in ->saved_raid_disk before clearing ->raid_disk 2/ when "re-add" is written to a device for which ->saved_raid_disk is not set, fail. I think this is suitable for stable as it can cause re-adding a device to be forced to do a full resync which takes a lot longer and so puts data at more risk. Cc: (v4.1) Fixes: 97f6cd39da22 ("md-cluster: re-add capabilities") Signed-off-by: NeilBrown Reviewed-by: Goldwyn Rodrigues Signed-off-by: Shaohua Li Signed-off-by: Greg Kroah-Hartman commit c0eb205dfe159d02bd7821288765ac0a40a0695c Author: Marcin Ziemianowicz Date: Sun Apr 29 15:01:11 2018 -0400 clk: at91: PLL recalc_rate() now using cached MUL and DIV values commit a982e45dc150da3a08907b6dd676b735391704b4 upstream. When a USB device is connected to the USB host port on the SAM9N12 then you get "-62" error which seems to indicate USB replies from the device are timing out. Based on a logic sniffer, I saw the USB bus was running at half speed. The PLL code uses cached MUL and DIV values which get set in set_rate() and applied in prepare(), but the recalc_rate() function instead queries the hardware instead of using these cached values. Therefore, if recalc_rate() is called between a set_rate() and prepare(), the wrong frequency is calculated and later the USB clock divider for the SAM9N12 SOC will be configured for an incorrect clock. In my case, the PLL hardware was set to 96 Mhz before the OHCI driver loads, and therefore the usb clock divider was being set to /2 even though the OHCI driver set the PLL to 48 Mhz. As an alternative explanation, I noticed this was fixed in the past by 87e2ed338f1b ("clk: at91: fix recalc_rate implementation of PLL driver") but the bug was later re-introduced by 1bdf02326b71 ("clk: at91: make use of syscon/regmap internally"). Fixes: 1bdf02326b71 ("clk: at91: make use of syscon/regmap internally) Cc: Signed-off-by: Marcin Ziemianowicz Acked-by: Boris Brezillon Signed-off-by: Stephen Boyd Signed-off-by: Greg Kroah-Hartman commit f216d1e9339dfb2981d2a0e44a15501cfa76f4ad Author: Robert Elliott Date: Thu May 31 18:36:36 2018 -0500 linvdimm, pmem: Preserve read-only setting for pmem devices commit 254a4cd50b9fe2291a12b8902e08e56dcc4e9b10 upstream. The pmem driver does not honor a forced read-only setting for very long: $ blockdev --setro /dev/pmem0 $ blockdev --getro /dev/pmem0 1 followed by various commands like these: $ blockdev --rereadpt /dev/pmem0 or $ mkfs.ext4 /dev/pmem0 results in this in the kernel serial log: nd_pmem namespace0.0: region0 read-write, marking pmem0 read-write with the read-only setting lost: $ blockdev --getro /dev/pmem0 0 That's from bus.c nvdimm_revalidate_disk(), which always applies the setting from nd_region (which is initially based on the ACPI NFIT NVDIMM state flags not_armed bit). In contrast, commit 20bd1d026aac ("scsi: sd: Keep disk read-only when re-reading partition") fixed this issue for SCSI devices to preserve the previous setting if it was set to read-only. This patch modifies bus.c to preserve any previous read-only setting. It also eliminates the kernel serial log print except for cases where read-write is changed to read-only, so it doesn't print read-only to read-only non-changes. Cc: Fixes: 581388209405 ("libnvdimm, nfit: handle unarmed dimms, mark namespaces read-only") Signed-off-by: Robert Elliott Signed-off-by: Dan Williams Signed-off-by: Greg Kroah-Hartman commit c6751cb1e828d7aa93cedfcee65534318278713e Author: Steffen Maier Date: Thu May 17 19:14:49 2018 +0200 scsi: zfcp: fix missing REC trigger trace on enqueue without ERP thread commit 6a76550841d412330bd86aed3238d1888ba70f0e upstream. Example trace record formatted with zfcpdbf from s390-tools: Timestamp : ... Area : REC Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 ZFCP_DBF_REC_TRIG Tag : ....... LUN : 0x... WWPN : 0x... D_ID : 0x... Adapter status : 0x... Port status : 0x... LUN status : 0x... Ready count : 0x... Running count : 0x... ERP want : 0x0. ZFCP_ERP_ACTION_REOPEN_... ERP need : 0xc0 ZFCP_ERP_ACTION_NONE Signed-off-by: Steffen Maier Cc: #2.6.38+ Reviewed-by: Benjamin Block Signed-off-by: Martin K. Petersen Signed-off-by: Greg Kroah-Hartman commit 2df7e6f33c64c61e9a33dbbed6bed4af78e94d67 Author: Steffen Maier Date: Thu May 17 19:14:48 2018 +0200 scsi: zfcp: fix missing REC trigger trace for all objects in ERP_FAILED commit 8c3d20aada70042a39c6a6625be037c1472ca610 upstream. That other commit introduced an inconsistency because it would trace on ERP_FAILED for all callers of port forced reopen triggers (not just terminate_rport_io), but it would not trace on ERP_FAILED for all callers of other ERP triggers such as adapter, port regular, LUN. Therefore, generalize that other commit. zfcp_erp_action_enqueue() already had two early outs which re-used the one zfcp_dbf_rec_trig() call. All ERP trigger functions finally run through zfcp_erp_action_enqueue(). So move the special handling for ZFCP_STATUS_COMMON_ERP_FAILED into zfcp_erp_action_enqueue() and add another early out with new trace marker for pseudo ERP need in this case. This removes all early returns from all ERP trigger functions so we always end up at zfcp_dbf_rec_trig(). Example trace record formatted with zfcpdbf from s390-tools: Timestamp : ... Area : REC Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 ZFCP_DBF_REC_TRIG Tag : ....... LUN : 0x... WWPN : 0x... D_ID : 0x... Adapter status : 0x... Port status : 0x... LUN status : 0x... Ready count : 0x... Running count : 0x... ERP want : 0x0. ZFCP_ERP_ACTION_REOPEN_... ERP need : 0xe0 ZFCP_ERP_ACTION_FAILED Signed-off-by: Steffen Maier Cc: #2.6.38+ Reviewed-by: Benjamin Block Signed-off-by: Martin K. Petersen Signed-off-by: Greg Kroah-Hartman commit 21224f6f135ab267b07729f3274fcfc028b3ace0 Author: Steffen Maier Date: Thu May 17 19:14:47 2018 +0200 scsi: zfcp: fix missing REC trigger trace on terminate_rport_io for ERP_FAILED commit d70aab55924b44f213fec2b900b095430b33eec6 upstream. For problem determination we always want to see when we were invoked on the terminate_rport_io callback whether we perform something or not. Temporal event sequence of interest with a long fast_io_fail_tmo of 27 sec: loose remote port t workqueue [s] zfcp_q_ IRQ zfcperp === ================== =================== ============================ 0 recv RSCN q p.test_link_work block rport start fast_io_fail_tmo send ADISC ELS 4 recv ADISC fail block zfcp_port port forced reopen send open port 12 recv open port fail q p.gid_pn_work zfcp_erp_wakeup (zfcp_erp_wait would return) GID_PN fail Before this point, we got a SCSI trace with tag "sctrpi1" on fast_io_fail, e.g. with the typical 5 sec setting. port.status |= ERP_FAILED If fast_io_fail_tmo triggers after this point, we missed a SCSI trace. workqueue fc_dl_ ================== 27 fc_timeout_fail_rport_io fc_terminate_rport_io zfcp_scsi_terminate_rport_io zfcp_erp_port_forced_reopen _zfcp_erp_port_forced_reopen if (port.status & ERP_FAILED) return; Therefore, write a trace before above early return. Example trace record formatted with zfcpdbf from s390-tools: Timestamp : ... Area : REC Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 ZFCP_DBF_REC_TRIG Tag : sctrpi1 SCSI terminate rport I/O LUN : 0xffffffffffffffff none (invalid) WWPN : 0x D_ID : 0x Adapter status : 0x... Port status : 0x... LUN status : 0x00000000 none (invalid) Ready count : 0x... Running count : 0x... ERP want : 0x03 ZFCP_ERP_ACTION_REOPEN_PORT_FORCED ERP need : 0xe0 ZFCP_ERP_ACTION_FAILED Signed-off-by: Steffen Maier Cc: #2.6.38+ Reviewed-by: Benjamin Block Signed-off-by: Martin K. Petersen Signed-off-by: Greg Kroah-Hartman commit 48ae373c57f009b32a03637e0809fabd9132fe81 Author: Steffen Maier Date: Thu May 17 19:14:46 2018 +0200 scsi: zfcp: fix missing REC trigger trace on terminate_rport_io early return commit 96d9270499471545048ed8a6d7f425a49762283d upstream. get_device() and its internally used kobject_get() only return NULL if they get passed NULL as argument. zfcp_get_port_by_wwpn() loops over adapter->port_list so the iteration variable port is always non-NULL. Struct device is embedded in struct zfcp_port so &port->dev is always non-NULL. This is the argument to get_device(). However, if we get an fc_rport in terminate_rport_io() for which we cannot find a match within zfcp_get_port_by_wwpn(), the latter can return NULL. v2.6.30 commit 70932935b61e ("[SCSI] zfcp: Fix oops when port disappears") introduced an early return without adding a trace record for this case. Even if we don't need recovery in this case, for debugging we should still see that our callback was invoked originally by scsi_transport_fc. Example trace record formatted with zfcpdbf from s390-tools: Timestamp : ... Area : REC Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 Tag : sctrpin SCSI terminate rport I/O, no zfcp port LUN : 0xffffffffffffffff none (invalid) WWPN : 0x WWPN D_ID : 0x N_Port-ID Adapter status : 0x... Port status : 0xffffffff unknown (-1) LUN status : 0x00000000 none (invalid) Ready count : 0x... Running count : 0x... ERP want : 0x03 ZFCP_ERP_ACTION_REOPEN_PORT_FORCED ERP need : 0xc0 ZFCP_ERP_ACTION_NONE Signed-off-by: Steffen Maier Fixes: 70932935b61e ("[SCSI] zfcp: Fix oops when port disappears") Cc: #2.6.38+ Reviewed-by: Benjamin Block Signed-off-by: Martin K. Petersen Signed-off-by: Greg Kroah-Hartman commit b0c2fc11ced965b01f174f69ecfac7feca48bc84 Author: Steffen Maier Date: Thu May 17 19:14:45 2018 +0200 scsi: zfcp: fix misleading REC trigger trace where erp_action setup failed commit 512857a795cbbda5980efa4cdb3c0b6602330408 upstream. If a SCSI device is deleted during scsi_eh host reset, we cannot get a reference to the SCSI device anymore since scsi_device_get returns !=0 by design. Assuming the recovery of adapter and port(s) was successful, zfcp_erp_strategy_followup_success() attempts to trigger a LUN reset for the half-gone SCSI device. Unfortunately, it causes the following confusing trace record which states that zfcp will do a LUN recovery as "ERP need" is ZFCP_ERP_ACTION_REOPEN_LUN == 1 and equals "ERP want". Old example trace record formatted with zfcpdbf from s390-tools: Tag: : ersfs_3 ERP, trigger, unit reopen, port reopen succeeded LUN : 0x WWPN : 0x D_ID : 0x Adapter status : 0x5400050b Port status : 0x54000001 LUN status : 0x40000000 ZFCP_STATUS_COMMON_RUNNING but not ZFCP_STATUS_COMMON_UNBLOCKED as it was closed on close part of adapter reopen ERP want : 0x01 ERP need : 0x01 misleading However, zfcp_erp_setup_act() returns NULL as it cannot get the reference. Hence, zfcp_erp_action_enqueue() takes an early goto out and _NO_ recovery actually happens. We always do want the recovery trigger trace record even if no erp_action could be enqueued as in this case. For other cases where we did not enqueue an erp_action, 'need' has always been zero to indicate this. In order to indicate above goto out, introduce an eyecatcher "flag" to mark the "ERP need" as 'not needed' but still keep the information which erp_action type, that zfcp_erp_required_act() had decided upon, is needed. 0xc_ is chosen to be visibly different from 0x0_ in "ERP want". New example trace record formatted with zfcpdbf from s390-tools: Tag: : ersfs_3 ERP, trigger, unit reopen, port reopen succeeded LUN : 0x WWPN : 0x D_ID : 0x Adapter status : 0x5400050b Port status : 0x54000001 LUN status : 0x40000000 ERP want : 0x01 ERP need : 0xc1 would need LUN ERP, but no action set up ^ Before v2.6.38 commit ae0904f60fab ("[SCSI] zfcp: Redesign of the debug tracing for recovery actions.") we could detect this case because the "erp_action" field in the trace was NULL. The rework removed erp_action as argument and field from the trace. This patch here is for tracing. A fix to allow LUN recovery in the case at hand is a topic for a separate patch. See also commit fdbd1c5e27da ("[SCSI] zfcp: Allow running unit/LUN shutdown without acquiring reference") for a similar case and background info. Signed-off-by: Steffen Maier Fixes: ae0904f60fab ("[SCSI] zfcp: Redesign of the debug tracing for recovery actions.") Cc: #2.6.38+ Reviewed-by: Benjamin Block Signed-off-by: Martin K. Petersen Signed-off-by: Greg Kroah-Hartman commit 97d3625bdd43e6816b179ea56a7aa58060069eee Author: Steffen Maier Date: Thu May 17 19:14:44 2018 +0200 scsi: zfcp: fix missing SCSI trace for retry of abort / scsi_eh TMF commit 81979ae63e872ef650a7197f6ce6590059d37172 upstream. We already have a SCSI trace for the end of abort and scsi_eh TMF. Due to zfcp_erp_wait() and fc_block_scsi_eh() time can pass between the start of our eh callback and an actual send/recv of an abort / TMF request. In order to see the temporal sequence including any abort / TMF send retries, add a trace before the above two blocking functions. This supports problem determination with scsi_eh and parallel zfcp ERP. No need to explicitly trace the beginning of our eh callback, since we typically can send an abort / TMF and see its HBA response (in the worst case, it's a pseudo response on dismiss all of adapter recovery, e.g. due to an FSF request timeout [fsrth_1] of the abort / TMF). If we cannot send, we now get a trace record for the first "abrt_wt" or "[lt]r_wait" which denotes almost the beginning of the callback. No need to explicitly trace the wakeup after the above two blocking functions because the next retry loop causes another trace in any case and that is sufficient. Example trace records formatted with zfcpdbf from s390-tools: Timestamp : ... Area : SCSI Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 Tag : abrt_wt abort, before zfcp_erp_wait() Request ID : 0x0000000000000000 none (invalid) SCSI ID : 0x SCSI LUN : 0x SCSI LUN high : 0x SCSI result : 0x SCSI retries : 0x SCSI allowed : 0x SCSI scribble : 0x SCSI opcode : FCP rsp inf cod: 0x.. none (invalid) FCP rsp IU : ... none (invalid) Timestamp : ... Area : SCSI Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 Tag : lr_wait LUN reset, before zfcp_erp_wait() Request ID : 0x0000000000000000 none (invalid) SCSI ID : 0x SCSI LUN : 0x SCSI LUN high : 0x SCSI result : 0x... unrelated SCSI retries : 0x.. unrelated SCSI allowed : 0x.. unrelated SCSI scribble : 0x... unrelated SCSI opcode : ... unrelated FCP rsp inf cod: 0x.. none (invalid) FCP rsp IU : ... none (invalid) Signed-off-by: Steffen Maier Fixes: 63caf367e1c9 ("[SCSI] zfcp: Improve reliability of SCSI eh handlers in zfcp") Fixes: af4de36d911a ("[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED") Cc: #2.6.38+ Reviewed-by: Benjamin Block Signed-off-by: Martin K. Petersen Signed-off-by: Greg Kroah-Hartman commit 9779f499d88f55df72cc504b830115aecea9cfbe Author: Steffen Maier Date: Thu May 17 19:14:43 2018 +0200 scsi: zfcp: fix missing SCSI trace for result of eh_host_reset_handler commit df30781699f53e4fd4c494c6f7dd16e3d5c21d30 upstream. For problem determination we need to see whether and why we were successful or not. This allows deduction of scsi_eh escalation. Example trace record formatted with zfcpdbf from s390-tools: Timestamp : ... Area : SCSI Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 Tag : schrh_r SCSI host reset handler result Request ID : 0x0000000000000000 none (invalid) SCSI ID : 0xffffffff none (invalid) SCSI LUN : 0xffffffff none (invalid) SCSI LUN high : 0xffffffff none (invalid) SCSI result : 0x00002002 field re-used for midlayer value: SUCCESS or in other cases: 0x2009 == FAST_IO_FAIL SCSI retries : 0xff none (invalid) SCSI allowed : 0xff none (invalid) SCSI scribble : 0xffffffffffffffff none (invalid) SCSI opcode : ffffffff ffffffff ffffffff ffffffff none (invalid) FCP rsp inf cod: 0xff none (invalid) FCP rsp IU : 00000000 00000000 00000000 00000000 none (invalid) 00000000 00000000 v2.6.35 commit a1dbfddd02d2 ("[SCSI] zfcp: Pass return code from fc_block_scsi_eh to scsi eh") introduced the first return with something other than the previously hardcoded single SUCCESS return path. Signed-off-by: Steffen Maier Fixes: a1dbfddd02d2 ("[SCSI] zfcp: Pass return code from fc_block_scsi_eh to scsi eh") Cc: #2.6.38+ Reviewed-by: Jens Remus Reviewed-by: Benjamin Block Signed-off-by: Martin K. Petersen Signed-off-by: Greg Kroah-Hartman commit f0c543159a4abad4412e55db33ac730c9f21684d Author: Himanshu Madhani Date: Sun Jun 3 22:09:53 2018 -0700 scsi: qla2xxx: Fix setting lower transfer speed if GPSC fails commit 413c2f33489b134e3cc65d9c3ff7861e8fdfe899 upstream. This patch prevents driver from setting lower default speed of 1 GB/sec, if the switch does not support Get Port Speed Capabilities (GPSC) command. Setting this default speed results into much lower write performance for large sequential WRITE. This patch modifies driver to check for gpsc_supported flags and prevents driver from issuing MBC_SET_PORT_PARAM (001Ah) to set default speed of 1 GB/sec. If driver does not send this mailbox command, firmware assumes maximum supported link speed and will operate at the max speed. Cc: stable@vger.kernel.org Signed-off-by: Himanshu Madhani Reported-by: Eda Zhou Reviewed-by: Ewan D. Milne Tested-by: Ewan D. Milne Signed-off-by: Martin K. Petersen Signed-off-by: Greg Kroah-Hartman commit 0400b066ea2f8730456e607bda3896e3985c2a1a Author: Martin Kelly Date: Mon Mar 26 14:27:51 2018 -0700 iio:buffer: make length types match kfifo types commit c043ec1ca5baae63726aae32abbe003192bc6eec upstream. Currently, we use int for buffer length and bytes_per_datum. However, kfifo uses unsigned int for length and size_t for element size. We need to make sure these matches or we will have bugs related to overflow (in the range between INT_MAX and UINT_MAX for length, for example). In addition, set_bytes_per_datum uses size_t while bytes_per_datum is an int, which would cause bugs for large values of bytes_per_datum. Change buffer length to use unsigned int and bytes_per_datum to use size_t. Signed-off-by: Martin Kelly Cc: Signed-off-by: Jonathan Cameron [bwh: Backported to 4.9: - Drop change to iio_dma_buffer_set_length() - Adjust filename, context] Signed-off-by: Ben Hutchings Signed-off-by: Greg Kroah-Hartman commit 3fd6a73da159049bade087487256af9030423975 Author: Liu Bo Date: Wed Jan 31 17:09:13 2018 -0700 Btrfs: fix unexpected cow in run_delalloc_nocow commit 5811375325420052fcadd944792a416a43072b7f upstream. Fstests generic/475 provides a way to fail metadata reads while checking if checksum exists for the inode inside run_delalloc_nocow(), and csum_exist_in_range() interprets error (-EIO) as inode having checksum and makes its caller enter the cow path. In case of free space inode, this ends up with a warning in cow_file_range(). The same problem applies to btrfs_cross_ref_exist() since it may also read metadata in between. With this, run_delalloc_nocow() bails out when errors occur at the two places. cc: v2.6.28+ Fixes: 17d217fe970d ("Btrfs: fix nodatasum handling in balancing code") Signed-off-by: Liu Bo Signed-off-by: David Sterba Signed-off-by: Sudip Mukherjee Signed-off-by: Greg Kroah-Hartman commit 77c82917d533ce49fff2731ddaa1dbc3fbfd9551 Author: Filipe Manana Date: Mon Jun 11 19:24:16 2018 +0100 Btrfs: fix return value on rename exchange failure commit c5b4a50b74018b3677098151ec5f4fce07d5e6a0 upstream. If we failed during a rename exchange operation after starting/joining a transaction, we would end up replacing the return value, stored in the local 'ret' variable, with the return value from btrfs_end_transaction(). So this could end up returning 0 (success) to user space despite the operation having failed and aborted the transaction, because if there are multiple tasks having a reference on the transaction at the time btrfs_end_transaction() is called by the rename exchange, that function returns 0 (otherwise it returns -EIO and not the original error value). So fix this by not overwriting the return value on error after getting a transaction handle. Fixes: cdd1fedf8261 ("btrfs: add support for RENAME_EXCHANGE and RENAME_WHITEOUT") CC: stable@vger.kernel.org # 4.9+ Signed-off-by: Filipe Manana Reviewed-by: David Sterba Signed-off-by: David Sterba Signed-off-by: Greg Kroah-Hartman commit 41b1d57a672f45f1d3a158cf28c24f1885201c9e Author: Maciej S. Szmigiero Date: Sat May 19 14:23:54 2018 +0200 X.509: unpack RSA signatureValue field from BIT STRING commit b65c32ec5a942ab3ada93a048089a938918aba7f upstream. The signatureValue field of a X.509 certificate is encoded as a BIT STRING. For RSA signatures this BIT STRING is of so-called primitive subtype, which contains a u8 prefix indicating a count of unused bits in the encoding. We have to strip this prefix from signature data, just as we already do for key data in x509_extract_key_data() function. This wasn't noticed earlier because this prefix byte is zero for RSA key sizes divisible by 8. Since BIT STRING is a big-endian encoding adding zero prefixes has no bearing on its value. The signature length, however was incorrect, which is a problem for RSA implementations that need it to be exactly correct (like AMD CCP). Signed-off-by: Maciej S. Szmigiero Fixes: c26fd69fa009 ("X.509: Add a crypto key parser for binary (DER) X.509 certificates") Cc: stable@vger.kernel.org Signed-off-by: James Morris Signed-off-by: Greg Kroah-Hartman commit 8fd86587ea975c2dc324c7c5bf804619bcea22b6 Author: Geert Uytterhoeven Date: Fri Jun 22 16:33:57 2018 +0200 time: Make sure jiffies_to_msecs() preserves non-zero time periods commit abcbcb80cd09cd40f2089d912764e315459b71f7 upstream. For the common cases where 1000 is a multiple of HZ, or HZ is a multiple of 1000, jiffies_to_msecs() never returns zero when passed a non-zero time period. However, if HZ > 1000 and not an integer multiple of 1000 (e.g. 1024 or 1200, as used on alpha and DECstation), jiffies_to_msecs() may return zero for small non-zero time periods. This may break code that relies on receiving back a non-zero value. jiffies_to_usecs() does not need such a fix: one jiffy can only be less than one µs if HZ > 1000000, and such large values of HZ are already rejected at build time, twice: - include/linux/jiffies.h does #error if HZ >= 12288, - kernel/time/time.c has BUILD_BUG_ON(HZ > USEC_PER_SEC). Broken since forever. Signed-off-by: Geert Uytterhoeven Signed-off-by: Thomas Gleixner Reviewed-by: Arnd Bergmann Cc: John Stultz Cc: Stephen Boyd Cc: linux-alpha@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180622143357.7495-1-geert@linux-m68k.org Signed-off-by: Greg Kroah-Hartman commit 344d6159fede9a3f7c7b846c662d3744ae89d132 Author: Huacai Chen Date: Tue Jun 12 17:54:42 2018 +0800 MIPS: io: Add barrier after register read in inX() commit 18f3e95b90b28318ef35910d21c39908de672331 upstream. While a barrier is present in the outX() functions before the register write, a similar barrier is missing in the inX() functions after the register read. This could allow memory accesses following inX() to observe stale data. This patch is very similar to commit a1cc7034e33d12dc1 ("MIPS: io: Add barrier after register read in readX()"). Because war_io_reorder_wmb() is both used by writeX() and outX(), if readX() need a barrier then so does inX(). Cc: stable@vger.kernel.org Signed-off-by: Huacai Chen Patchwork: https://patchwork.linux-mips.org/patch/19516/ Signed-off-by: Paul Burton Cc: James Hogan Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang Cc: Zhangjin Wu Cc: Huacai Chen Signed-off-by: Greg Kroah-Hartman commit db2baeef79d1d0ff0fac4589f8d7dc215ea36889 Author: Tetsuo Handa Date: Fri May 11 19:54:19 2018 +0900 printk: fix possible reuse of va_list variable commit 988a35f8da1dec5a8cd2788054d1e717be61bf25 upstream. I noticed that there is a possibility that printk_safe_log_store() causes kernel oops because "args" parameter is passed to vsnprintf() again when atomic_cmpxchg() detected that we raced. Fix this by using va_copy(). Link: http://lkml.kernel.org/r/201805112002.GIF21216.OFVHFOMLJtQFSO@I-love.SAKURA.ne.jp Cc: Peter Zijlstra Cc: Steven Rostedt Cc: dvyukov@google.com Cc: syzkaller@googlegroups.com Cc: fengguang.wu@intel.com Cc: linux-kernel@vger.kernel.org Signed-off-by: Tetsuo Handa Fixes: 42a0bb3f71383b45 ("printk/nmi: generic solution for safe printk in NMI") Cc: 4.7+ # v4.7+ Reviewed-by: Sergey Senozhatsky Signed-off-by: Petr Mladek Signed-off-by: Greg Kroah-Hartman commit ca558fb836d3b04fbda144fa22e295d5f41bc2de Author: Mika Westerberg Date: Wed May 23 17:14:39 2018 -0500 PCI: pciehp: Clear Presence Detect and Data Link Layer Status Changed on resume commit 13c65840feab8109194f9490c9870587173cb29d upstream. After a suspend/resume cycle the Presence Detect or Data Link Layer Status Changed bits might be set. If we don't clear them those events will not fire anymore and nothing happens for instance when a device is now hot-unplugged. Fix this by clearing those bits in a newly introduced function pcie_reenable_notification(). This should be fine because immediately after, we check if the adapter is still present by reading directly from the status register. Signed-off-by: Mika Westerberg Signed-off-by: Bjorn Helgaas Reviewed-by: Rafael J. Wysocki Reviewed-by: Andy Shevchenko Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman commit 0d3d58337d4bd414d069c1f4d6330e02ef2ecd1e Author: Mika Westerberg Date: Fri Apr 27 13:06:30 2018 -0500 PCI: Add ACS quirk for Intel 300 series commit f154a718e6cc0d834f5ac4dc4c3b174e65f3659e upstream. Intel 300 series chipset still has the same ACS issue as the previous generations so extend the ACS quirk to cover it as well. Signed-off-by: Mika Westerberg Signed-off-by: Bjorn Helgaas CC: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman commit 5e1deade6064d088ad4852f9a2299eeeefdfe3d2 Author: Alex Williamson Date: Wed Apr 25 14:27:37 2018 -0600 PCI: Add ACS quirk for Intel 7th & 8th Gen mobile commit e8440f4bfedc623bee40c84797ac78d9303d0db6 upstream. The specification update indicates these have the same errata for implementing non-standard ACS capabilities. Signed-off-by: Alex Williamson Signed-off-by: Bjorn Helgaas CC: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman commit 83f9549d650b477b46fc070461f82ef536eae702 Author: Tokunori Ikegami Date: Sun Jun 3 23:02:01 2018 +0900 MIPS: BCM47XX: Enable 74K Core ExternalSync for PCIe erratum commit 2a027b47dba6b77ab8c8e47b589ae9bbc5ac6175 upstream. The erratum and workaround are described by BCM5300X-ES300-RDS.pdf as below. R10: PCIe Transactions Periodically Fail Description: The BCM5300X PCIe does not maintain transaction ordering. This may cause PCIe transaction failure. Fix Comment: Add a dummy PCIe configuration read after a PCIe configuration write to ensure PCIe configuration access ordering. Set ES bit of CP0 configu7 register to enable sync function so that the sync instruction is functional. Resolution: hndpci.c: extpci_write_config() hndmips.c: si_mips_init() mipsinc.h CONF7_ES This is fixed by the CFE MIPS bcmsi chipset driver also for BCM47XX. Also the dummy PCIe configuration read is already implemented in the Linux BCMA driver. Enable ExternalSync in Config7 when CONFIG_BCMA_DRIVER_PCI_HOSTMODE=y too so that the sync instruction is externalised. Signed-off-by: Tokunori Ikegami Reviewed-by: Paul Burton Acked-by: Hauke Mehrtens Cc: Chris Packham Cc: Rafał Miłecki Cc: linux-mips@linux-mips.org Cc: stable@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/19461/ Signed-off-by: James Hogan Signed-off-by: Greg Kroah-Hartman commit 5fdb3c468b515694159583d01a3154e0ffa4a81f Author: Joakim Tjernlund Date: Wed Jun 6 12:13:30 2018 +0200 mtd: cfi_cmdset_0002: Avoid walking all chips when unlocking. commit f1ce87f6080b1dda7e7b1eda3da332add19d87b9 upstream. cfi_ppb_unlock() walks all flash chips when unlocking sectors, avoid walking chips unaffected by the unlock operation. Fixes: 1648eaaa1575 ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking") Cc: stable@vger.kernel.org Signed-off-by: Joakim Tjernlund Signed-off-by: Boris Brezillon Signed-off-by: Greg Kroah-Hartman commit b4e24c2842e15f221ac3527af781d7b8940b5cfb Author: Joakim Tjernlund Date: Wed Jun 6 12:13:29 2018 +0200 mtd: cfi_cmdset_0002: Fix unlocking requests crossing a chip boudary commit 0cd8116f172eed018907303dbff5c112690eeb91 upstream. The "sector is in requested range" test used to determine whether sectors should be re-locked or not is done on a variable that is reset everytime we cross a chip boundary, which can lead to some blocks being re-locked while the caller expect them to be unlocked. Fix the check to make sure this cannot happen. Fixes: 1648eaaa1575 ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking") Cc: stable@vger.kernel.org Signed-off-by: Joakim Tjernlund Signed-off-by: Boris Brezillon Signed-off-by: Greg Kroah-Hartman commit 0bf4e48c20ca447e577c77bfc9205f1c8890c65d Author: Joakim Tjernlund Date: Wed Jun 6 12:13:28 2018 +0200 mtd: cfi_cmdset_0002: fix SEGV unlocking multiple chips commit 5fdfc3dbad099281bf027a353d5786c09408a8e5 upstream. cfi_ppb_unlock() tries to relock all sectors that were locked before unlocking the whole chip. This locking used the chip start address + the FULL offset from the first flash chip, thereby forming an illegal address. Fix that by using the chip offset(adr). Fixes: 1648eaaa1575 ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking") Cc: stable@vger.kernel.org Signed-off-by: Joakim Tjernlund Signed-off-by: Boris Brezillon Signed-off-by: Greg Kroah-Hartman commit 552eacd58ee4c930f313f8e01f4cee75fc48afed Author: Joakim Tjernlund Date: Wed Jun 6 12:13:27 2018 +0200 mtd: cfi_cmdset_0002: Use right chip in do_ppb_xxlock() commit f93aa8c4de307069c270b2d81741961162bead6c upstream. do_ppb_xxlock() fails to add chip->start when querying for lock status (and chip_ready test), which caused false status reports. Fix that by adding adr += chip->start and adjust call sites accordingly. Fixes: 1648eaaa1575 ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking") Cc: stable@vger.kernel.org Signed-off-by: Joakim Tjernlund Signed-off-by: Boris Brezillon Signed-off-by: Greg Kroah-Hartman commit e9dc5dce0925ea4412345ca034bba9a252de2783 Author: Tokunori Ikegami Date: Wed May 30 18:32:26 2018 +0900 mtd: cfi_cmdset_0002: Change write buffer to check correct value commit dfeae1073583dc35c33b32150e18b7048bbb37e6 upstream. For the word write it is checked if the chip has the correct value. But it is not checked for the write buffer as only checked if ready. To make sure for the write buffer change to check the value. It is enough as this patch is only checking the last written word. Since it is described by data sheets to check the operation status. Signed-off-by: Tokunori Ikegami Reviewed-by: Joakim Tjernlund Cc: Chris Packham Cc: Brian Norris Cc: David Woodhouse Cc: Boris Brezillon Cc: Marek Vasut Cc: Richard Weinberger Cc: Cyrille Pitchen Cc: linux-mtd@lists.infradead.org Cc: stable@vger.kernel.org Signed-off-by: Boris Brezillon Signed-off-by: Greg Kroah-Hartman commit afe249e3e38d51e58eba9b6992646a1f8070883d Author: Leon Romanovsky Date: Tue May 29 14:56:14 2018 +0300 RDMA/mlx4: Discard unknown SQP work requests commit 6b1ca7ece15e94251d1d0d919f813943e4a58059 upstream. There is no need to crash the machine if unknown work request was received in SQP MAD. Cc: # 3.6 Fixes: 37bfc7c1e83f ("IB/mlx4: SR-IOV multiplex and demultiplex MADs") Signed-off-by: Leon Romanovsky Signed-off-by: Doug Ledford Signed-off-by: Greg Kroah-Hartman commit 52e167187be8b584673204f6d87b07aff7725e47 Author: Max Gurtovoy Date: Thu May 31 11:05:23 2018 +0300 IB/isert: fix T10-pi check mask setting commit 0e12af84cdd3056460f928adc164f9e87f4b303b upstream. A copy/paste bug (probably) caused setting of an app_tag check mask in case where a ref_tag check was needed. Fixes: 38a2d0d429f1 ("IB/isert: convert to the generic RDMA READ/WRITE API") Fixes: 9e961ae73c2c ("IB/isert: Support T10-PI protected transactions") Cc: stable@vger.kernel.org Reviewed-by: Christoph Hellwig Reviewed-by: Sagi Grimberg Reviewed-by: Martin K. Petersen Signed-off-by: Max Gurtovoy Signed-off-by: Jason Gunthorpe Signed-off-by: Greg Kroah-Hartman commit a664281b85e01066336a0eb46bd09054c0705009 Author: Alex Estrin Date: Tue May 15 18:31:39 2018 -0700 IB/isert: Fix for lib/dma_debug check_sync warning commit 763b69654bfb88ea3230d015e7d755ee8339f8ee upstream. The following error message occurs on a target host in a debug build during session login: [ 3524.411874] WARNING: CPU: 5 PID: 12063 at lib/dma-debug.c:1207 check_sync+0x4ec/0x5b0 [ 3524.421057] infiniband hfi1_0: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x0000000000000000] [size=76 bytes] ......snip ..... [ 3524.535846] CPU: 5 PID: 12063 Comm: iscsi_np Kdump: loaded Not tainted 3.10.0-862.el7.x86_64.debug #1 [ 3524.546764] Hardware name: Dell Inc. PowerEdge R430/03XKDV, BIOS 1.2.6 06/08/2015 [ 3524.555740] Call Trace: [ 3524.559102] [] dump_stack+0x19/0x1b [ 3524.565477] [] __warn+0xd8/0x100 [ 3524.571557] [] warn_slowpath_fmt+0x5f/0x80 [ 3524.578610] [] check_sync+0x4ec/0x5b0 [ 3524.585177] [] ? set_cpus_allowed_ptr+0x5f/0x1c0 [ 3524.592812] [] debug_dma_sync_single_for_cpu+0x80/0x90 [ 3524.601029] [] ? x2apic_send_IPI_mask+0x13/0x20 [ 3524.608574] [] ? native_smp_send_reschedule+0x5b/0x80 [ 3524.616699] [] ? resched_curr+0xf6/0x140 [ 3524.623567] [] isert_create_send_desc.isra.26+0xe0/0x110 [ib_isert] [ 3524.633060] [] isert_put_login_tx+0x55/0x8b0 [ib_isert] [ 3524.641383] [] ? try_to_wake_up+0x1a4/0x430 [ 3524.648561] [] iscsi_target_do_tx_login_io+0xdd/0x230 [iscsi_target_mod] [ 3524.658557] [] iscsi_target_do_login+0x1a7/0x600 [iscsi_target_mod] [ 3524.668084] [] ? kstrdup+0x49/0x60 [ 3524.674420] [